14
Oct
This application will be more like what youd get shooting paint. Smooth the area with a Scotchbrite pad once the surface is dry.
The outer surface of a fiberglass boat is normally a special resin called gelcoat.
How to apply gelcoat to fiberglass boat. Apply the gelcoat using a brush if youre covering a small area. To apply the gelcoat with a brush dip the brush in the gelcoat so theres a liberal amount of gelcoat on it. Brush the gelcoat onto.
Use a sandblaster to blast the gelcoat away from the fiberglass. Grind the gelcoat away from the fiberglass using a grinder and 36-grit griding discs on a soft grinding pad. Scrub the entire area with detergent and then rinse with clean water.
Smooth the area with a Scotchbrite pad once the surface is dry. Similarly how do you apply gelcoat to the bottom of a boat. Step 1 - Clean Your Boat Thoroughly.
Complete the first gelcoat then wait four hours before applying another. The first coat will still be tacky. Press on the coat with your finger.
It shouldnt leave an impression with your fingernail. Apply a second coat and allow to harden for another four hours minimum. This coat will be tacky but hard enough to resist leaving a fingernail impression.
Step 2 - Apply the Gelcoat Making sure that your gelcoat is applied evenly on the paintbrush go over the base of the boat beginning on one side and working your way over. Make sure that you give your boat a thick layer as a thin layer may not give a complete seal. First thing you want to do is look at the surface you want to apply gelcoat to.
If the surface is already covered with gelcoat or if the surface is a fiberglass or polyester resin then applying gelcoat will be a snap. If the surface is paint then the paint would have. Starting with 40 or 80 grit and finishing with 100 or 200 grit use low-grade sandpaper and scale it up.
That should remove debris and rough up the surface sufficiently to bind with a fresh gelcoat. The trick will be accomplished by a power sander bringing the blistered region back to the fiberglass. Mix the Gelcoat.
After you have color-matched the amount of gelcoat needed for the repair add catalyst aka hardener. Different gelcoat resins require different catalysts so make sure you are using the proper formula as well as the right two-part ratio eg four drops of. Home Boat Design Forums Construction Boatbuilding Fiberglass and Composite Boat Building two tone gelcoat application.
Discussion in Fiberglass and Composite Boat Building started by jiggerpro Oct 29 2014. How to Apply Clear Coat to a Fiberglass Boat. KBS DiamondFinish Clear restores a lasting gloss to your boats aging gelcoat.
Seamanship Lessons From a Yacht Captain. How to Buy a Boat in a Boom Market. The outer surface of a fiberglass boat is normally a special resin called gelcoat.
Gelcoat has little structural value but gelcoat protects the hull and gives it its color and shine. The ultra high gloss most new boats exhibit is due entirely to the highly polished mirror-like surface of the mold used in the original construction of the boat. Time and exposure eventually erode the relatively.
Buff and polish your boat with a suitable polishing compound. This abrasive compound will gently remove small scratches stains and other imperfections whilst restoring the gelcoats natural shine. The final step is to apply the boat wax of choice with a clean soft cloth.
Allow the wax to dry. Use KBS Klean a concentrated water-based cleaning solution. Dilute with 10 parts warm water to one part of KBS Klean and use a spray bottle to liberally wet the surface.
Scrub thoroughly with a. The final gelcoat application will be done with a 1 mm tip gun adding between 30 - 40 patch booster 10 surfacing wax. This application will be more like what youd get shooting paint.
Because of the lowered viscosity watch out for sags and runs. A good wash will ensure that your fiberglass has a smooth surface and therefore that the gelcoat will pour or spray evenly onto the boat. Once you have washed the fiberglass give the area where you will be pouring your gelcoat a good buffing with some sandpaper.
In todays episode we are painting the deck of the boat. 522011 Hold the spray gun about 1 foot 030 m away from the fiberglass and spray the gelcoat onto it in short even strokes. 11262007 Simply rub away the oxidation until the gelcoat shines and then apply the Premium Boat Shine.
Welcome back to Zachs Garage. New and used models for sale. Gelcoat should be applied in temperatures of 60ºF to 80ºF.
Always use eye and hand protection. Gelcoat should not be applied over paint wood metal or concrete. It usually will not adhere to these surfaces.
Gelcoat will not fully cure without adding a surfacing agent or wax additive sanding aid. You can over-spray with PVA before gel coal reaches its gel stage 5-10 min or adding 1oz per quart. And therefore it is probably the single most important coating on your boat.
A barrier coat seals a fiberglass hull blocking water entry and inhibiting blister formation in underwater gelcoat and fiberglass. If your boat has a fiberglass hull you MUST protect it. The outer surface of a fiberglass boat is normally a special resin called gelcoat.
Gelcoat has little structural value the underlying laminates of resin-saturated glass fabric provide that but gelcoat protects the hull and gives it its color and shine.