How to make an eye splice in 3 strand rope

This is a simple all-purpose eye retains 90-100 of average new rope strength. I buy a 3-strand dockline that come pre-spliced with a 12 eye on one end to place over a bow cleat and I tie a rolling hitch to the chain.

In this video i show you step by step how to tie and eye splice in a 3 strand rope a easy to follow tutorial.

How to make an eye splice in 3 strand rope. Lay out the eye then get the middle strand and put it under another going AGAINST the braid. Make sure you give the strand a good twist once it is through. This will make for a neater splice.

Eye Splice a Rope - How to Eye Splice a 3 Strand Rope - Easy to Follow Splicing Revisited - YouTube. How to make an eye splice with a 3 strand rope - YouTube. In this video i show you step by step how to tie and eye splice in a 3 strand rope a easy to follow tutorial.

Perfect for a permanent. You should have 3 strands tape the bitter end of each strand to prevent it from unraveling and label each one with the sharpie marker as 1 2 and 3 figure 1. From the taped end form a loop the size you want and then mark a line around the standing part of the line figure 2 below.

The correct length to unravel is about 3 times the diameter per tuck ie for five tucks in half inch diameter rope leave the free strands at least 75 inches long. And for seven tucks at least 105 inches. Create the required size of loop and mark the rope.

Untwist the rope one half turn open the top or center bight with a small fid and stick the center strand under the center bight from right to left then stick the left strand under the next bight to the left in the same direction and lastly stick the right strand from right to left under the remaining bight. Unlay the three strands at the end of the rope the working end enough to make at least three tucks about one turn for each tuck and form an eye by laying the opened strands on top of the standing part of the rope The part of the rope you splice into Take the middle end A and tuck it from right to left underneath the. I just stick with my inexpensive effortless time tested method.

I buy a 3-strand dockline that come pre-spliced with a 12 eye on one end to place over a bow cleat and I tie a rolling hitch to the chain. They are commonly available in various sizes and lengths. We anchor a lot so I just order a new one when it gets dirty enough or chafes.

A simplier eye splice is the Samson 12-strand Class II eye splice. This is a simple all-purpose eye retains 90-100 of average new rope strength. An eye is formed into the rope and the tail is buried into the standing part.

The key to using this simple. Secure loop in the end of 3 or 4-strand rope. Makes an adjustable splice for multi-strand rope.

Creates a rope loop using hollow-braid rope. Hollow Braid Eye Splice with end threaded up rope center. McDonalds quick Brummel splice for hollow braid rope.

Makes a secure join between two pieces of stranded rope. Narration —- For eye splice knotboard 12 Count back and unlay 5 rounds of the lay of the rope. 3 Fan the unlayed end of the rope and place it over the standing part of the rope.

The strand to the inside of the eye must look like it is coming out from under the other. To do that particular splicego to a spot on the rope a bit above where you want the eye to be start opening up the lay by twisting against it. Keep opening up twisting until you have as much length as you need to get say 4 or more tucks into the standing part.

Decide size of eye you need. Cut off strand pairs 1 3 and 5. Tuck strand pairs 2 4 and 6 for additional 3 tucks retain twist and remove excess slack.

Figure 2 Step 3 Rope is comprised of a total of 12 strands six 6 strands with left hand twist and six 6 strands with right hand twist. Select one left twist strand and one right twist strand and tape togeth-er. 3-Strand Tuck Eye Splice.

Class 1 3-strand ropes are made from any or all of the following fibers. Although the 3-strand splice is the most common splice and simple to perform technique is important to preserve splice strength. Lift a strand on the standing part of the rope at the point where you want the eye to close and tuck the center strand under it.

On smaller andor soft-lay rope you will be able to make the tucks just using your fingers. Large stiff or old line may require use of a fid or marlinespike to open the strands in. Once all three strands have been tucked for the first time you can continue to weave or braid them through the body of the rope.

Take off the tape and make sure all three strands are tight before you begin. Pick up the centre strand and pass this under the strand two above the one it is currently under. Turn the rope clockwise by about a third and repeat this process with the left-hand.

You need to insert each of the three strands in the right place otherwise you cannot go further. Depending how big or small you want to make your loop choose the position where you want to start inserting the rope. Take the strand in the middle lets call this one number 1 and pass it under your chosen strand of the rope itself.

Splices in ropes make the rope secure and ready to go when needed. There are a number of rather complicated splices. The eye splice back splice and short splice are basic and well suited to the type of pioneering outlined in this pamphlet The splices shown here can be made in any three strand rope manila sisal poly or nylon.

A 3-Strand Eye Splice page 6. 3 tucking strands step Class I ropes are made from any or all of the following fibers. Olefin polyester or nylon.

Although the 3-strand splice is the most common splice and simple to perform technique is important to preserve splice strength. Take care that the tucks lie neatly as rope strength can be lost.